[Sep 09, 2024] New 2024 Cisco 300-410 Exam Dumps with PDF from PremiumVCEDump (Updated 575 Questions) [Q232-Q249]

9 Sep, 2024 By admin 300-410, Cisco 0 Comments

[Sep 09, 2024] New 2024 Cisco 300-410 Exam Dumps with PDF from PremiumVCEDump (Updated 575 Questions) [Q232-Q249]

Rate this post

New 2024 300-410 exam questions Welcome to download the newest PremiumVCEDump 300-410 PDF dumps (575 Q&As)

P.S. Free 2024 CCNP Enterprise 300-410 dumps are available on Google Drive shared by PremiumVCEDump

NEW QUESTION 232
Refer to Exhibit.
A network administrator has successfully configured DMVPN topology between a hub and two spoke routers. Which two configuration commands should establish direct communications between spoke 1 and spoke 2 without going through the hub? (Choose two).

At the hub router, configure the ip nhrp shortcut command.

At the spoke routers, configure the ip nhrp spoke-tunnel command.

At the hub router, configure ip nhrp redirect the command

At the spoke routers, configure the ip nhrp shortcut command.

At the hub router, configure tne Ip nhrp spoke-tunnel command

NEW QUESTION 233
What does the PE router convert the Ipv4 prefix to within an MPLS VPN?

VPN-IPv4 prefix combined with the 64-bit route distinguisher

48-bit route combining the IP and PE router-id

prefix that combines the ASN, PE router-id, and IP prefix

eBGP path association between the PE and CE sessions

NEW QUESTION 234
Refer to the exhibit.

Refer to the exhibit. An engineer notices a connectivity problem between routers R1 and R2. The frequency of this problem is high during peak business hours. Which action resolves the issue?

Increase the MTU on the interfaces that connect R1 and R2.

Increase the available bandwidth between R1 and R2.

Decrease the EIGRP keepallve and hold down timers on R1 and R2.

Set static EIGRP neighborship between R1 and R2.

NEW QUESTION 235
Refer to the exhibit.

Which configuration configures a policy on R1 to forward any traffic that is sourced from the 192.168.130.0/24 network to R2?

Option A

Option B

Option C

Option D

NEW QUESTION 236
Refer to the exhibit.

An engineer configured NetFlow on R1, but the NMS server cannot see the flow from R1. Which configuration resolves the issue?

flow monitor Flowmonitor1
destination 10.221.10.11

flow exporter FlowAnalyzer1
destination 10.221.10.11

interface Ethernet0/1
flow-destination 10.221.10.11

interface Ethernet0/0
flow-destination 10.221.10.11

NEW QUESTION 237

Refer to the exhibit. The network administrator configured the branch router for IPv6 on the E 0/0 interface The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?

Enable the IPv4 address family under the E 0/0 interface by using the address-family Ipv4 unicast command

Disable IPv6 on the E 0/0 interface using the no ipv6 enable command

Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command

Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E 0/0 interface.

NEW QUESTION 238
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?

Interface-dispoint

Shared risk link group-disjoint

Linecard-disjoint

Lowest-repair-path-metric

NEW QUESTION 239
Refer to the exhibit.

AS111 is receiving its own routes from AS200 causing a loop in the network. Which configuration provides loop prevention?

NEW QUESTION 240
Refer to Exhibit.

Traffic from the branch network should route through HQ R1 unless the path is unavailable. An engineer tests this functionality by shutting down interface on the BRANCH router toward HQ_R1 router but
192.168.20.0/24 is no longer reachable from the branch router. Which set of configurations resolves the issue?

HQ_R1(config)# ip sla responder
HQ_R1(config)# ip sla responder icmp-echo 172.16.35.2

BRANCH(config)# ip sla 1
BRANCH(config-ip-sla)# icmp-echo 172.16.35.1

HQ_R2(config)# ip sla responder
HQ_R2(config)# ip sla responder icmp-echo 172.16.35.5

BRANCH(config)# ip sla 1
BRANCH(config-ip-sla)# icmp-echo 172.16.35.2

NEW QUESTION 241

Refer to the exhibit. an engineer is trying to get 192.168.32.100 forwarded through 10.1.1.1, but it was forwarded through 10.1.1.2. What action forwards the packets through 10.1.1.1?

Configure EIGRP to receive 192.168.32.0 route with lower admin distance.

Configure EIGRP to receive 192.168.32.0 route with longer prefix than /19.

Configure EIGRP to receive 192.168.32.0 route with lower metric.

Configure EIGRP to receive 192.168.32.0 route with equal or longer prefix than /24.

NEW QUESTION 242

Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?

Change the direction of the distribute-list command from out to in.

Remove the line with the sequence number 5 from the prefix list.

Remove the prefix keyword from the distribute-list command.

Remove the line with the sequence number 10 from the prefix list.

NEW QUESTION 243
Refer to the exhibit.

A network engineer finds that PC1 is accessing the hotel website to do the booking but fails to make payment.
Which action resolves the issue?

Allow stub network 10.10.202.168/30 on router R3 OSPF.

Decrease the AD to 5 OSPF route 192.168.94.0 on R1.

Increase the AD to 200 of static route 192.168.94.0 on R3.

Configure a reverse route on R1 for PC1 172.16.1.0/24.

NEW QUESTION 244
configuration on the hub router meets this requirement?

interface Tunnel0
tunnel mode gre multipoint

interface Tunnel0 tunnel mode dvmrp

interface Tunnel0 tunnel mode ipsec ipv4

interface Tunnel0 tunnel mode ip

NEW QUESTION 245
Refer to the exhibit.

What is the result if applying this configuration?

The router can form BGP neighborships with any other device.

The router can form BGP neighborships with any device that matched by the access list named ”BGP”

The router cannot form BGP neighborships with any other device

The router cannot form BGP neighborships with any device that is matched by the access list named ”BGP”

NEW QUESTION 246
Refer to the exhibit.

The R1 and R2 configurations are:

The neighbor is not coming up. Which two sets of configurations bring the neighbors up? (Choose two.)

R2
ip route 10.1.1.1 255.255.255.255 192.168.1.1
router bgp 200
neighbor 10.1.1.1 tti-security hops 1
neighbor 10.1.1.1 update-source loopback 0

R2
ip route 10.1.1.1 255.255.255.255 192.168.1.1
router bgp 200
neighbor 10.1.1.1 disable-connected-check
neighbor 10.1.1.1 update-source loopback 0

R2
ip route 10.1.1.2 255.255.255.255 192.168.1.2
router bgp 100neighbor 10.1.1.2 ttl-security hops 1
neighbor 10.1.1.2 update-source loopback 0

R1
ip route 10.1.1.2 255.255.255.255 192.168.1.2
router bgp 100
neighbor 10.1.1.1 ttl-security hops 1
neighbor 10.1.1.2 update-source loopback 0

R1
ip route 10.1.1.2 255.255.255.255 192.168.1.2
router bgp 100
neighbor 10.1.1.2 disable-connected-check
neighbor 10.1.1.2 update-source Loopback0

NEW QUESTION 247
An engineer configured access list NON-CISCO in a policy to influence routes.

What are the two effects of this route map configuration? (Choose two.)

Packets are forwarded using normal route lookup.

Packets are forwarded to the default gateway.

Packets are dropped by the access list.

Packets are evaluated by sequence 10.

Packets are not evaluated by sequence 10.

NEW QUESTION 248
Refer to the exhibit.

The administrator is trying to overwrite an existing file on the TFTP server that was previously uploaded by another router. However, the attempt to update the file fails. Which action resolves this issue?