Download Fortinet NSE7_SDW-7.0 Mock Test Study Material [Q32-Q48]

20 Jul, 2024 By admin NSE7_SDW-7.0, Fortinet 0 Comments

Download Fortinet NSE7_SDW-7.0 Mock Test Study Material [Q32-Q48]

4/5 - (1 vote)

Download Fortinet NSE7_SDW-7.0 Mock Test Study Material

NSE7_SDW-7.0 Questions Prepare with Learning Information

NO.32 Refer to the exhibits.
Exhibit A

Exhibit B –

Exhibit A shows the configuration for an SD-WAN rule and exhibit B shows the respective rule status, the routing table, and the member status.
The administrator wants to understand the expected behavior for traffic matching the SD-WAN rule.
Based on the exhibits, what can the administrator expect for traffic matching the SD-WAN rule?

The traffic will be load balanced across all three overlays.

The traffic will be routed over T_INET_0_0.

The traffic will be routed over T_MPLS_0.

The traffic will be routed over T_INET_1_0.

NO.33 Which two tasks are part of using central VPN management? (Choose two.)

You can configure full mesh, star, and dial-up VPN topologies.

You must enable VPN zones for SD-WAN deployments.

FortiManager installs VPN settings on both managed and external gateways.

You configure VPN communities to define common IPsec settings shared by all VPN gateways.

NO.34

Exhibit B –

Exhibit A shows the system interface with the static routes and exhibit B shows the firewall policies on the managed FortiGate.
Based on the FortiGate configuration shown in the exhibits, what issue might you encounter when creating an SD-WAN zone for port1 and port2?

port1 is assigned a manual IP address.

port1 is referenced in a firewall policy.

port2 is referenced in a static route.

port1 and port2 are not administratively down.

NO.35 Refer to the exhibits.

Exhibit A shows the packet duplication rule configuration, the SD-WAN zone status output, and the sniffer output on FortiGate acting as the sender. Exhibit B shows the sniffer output on a FortiGate acting as the receiver.
The administrator configured packet duplication on both FortiGate devices. The sniffer output on the sender FortiGate shows that FortiGate forwards an ICMP echo request packet over three overlays, but it only receives one reply packet through T_INET_1_0.
Based on the output shown in the exhibits, which two reasons can cause the observed behavior? (Choose two.)

On the receiver FortiGate, packet-de-duplication is enabled.

The ICMP echo request packets sent over T_INET_0_0 and T_MPLS_0 were dropped along the way.

The ICMP echo request packets received over T_INET_0_0 and T_MPLS_0 were offloaded to NPU.

On the sender FortiGate, duplication-max-num is set to 3.

NO.36 Refer to the exhibit.

Which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules?

All traffic from a source IP to a destination IP is sent to the same interface.

All traffic from a source IP is sent to the same interface.

All traffic from a source IP is sent to the most used interface.

All traffic from a source IP to a destination IP is sent to the least used interface.

NO.37 Refer to the exhibit.

Based on the exhibit, which statement about FortiGate re-evaluating traffic is true?

The type of traffic defined and allowed on firewall policy ID 1 is UDP.

FortiGate has terminated the session after a change on policy ID 1.

Changes have been made on firewall policy ID 1 on FortiGate.

Firewall policy ID 1 has source NAT disabled.

NO.38 What are two reasons why FortiGate would be unable to complete the zero-touch provisioning process?
(Choose two.)

The FortiGate cloud key has not been added to the FortiGate cloud portal.

FortiDeploy has connected with FortiGate and provided the initial configuration to contact FortiManager

The zero-touch provisioning process has completed internally, behind FortiGate.

FortiGate has obtained a configuration from the platform template in FortiGate cloud.

A factory reset performed on FortiGate.

NO.39 Refer to the exhibit.

The device exchanges routes using IBGP.
Which two statements are correct about the IBGP configuration and routing information on the device? (Choose two.)

Each BGP route is three hops away from the destination.

ibgp-multipath is disabled.

additional-path is enabled.

You can run the get router info routing-table database command to display the additional paths.

NO.40 Which two statements are correct when traffic matches the implicit SD-WAN rule? (Choose two.)

The sdwan_service_id flag in the session information is 0.

All SD-WAN rules have the default setting enabled.

Traffic does not match any of the entries in the policy route table.

Traffic is load balanced using the algorithm set for the v4-ecmp-mode setting.

NO.41 Refer to the exhibit.

Based on the exhibit, which two actions does FortiGate perform on sessions after a firewall policy change? (Choose two.)

FortiGate flushes all sessions.

FortiGate terminates the old sessions.

FortiGate does not change existing sessions.

FortiGate evaluates new sessions.

NO.42 Exhibit.

Which conclusion about the packet debug flow output is correct?

The total number of daily sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.

The packet size exceeded the outgoing interface MTU.

The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.

The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the firewall policy, and the packet was dropped.

NO.43 Refer to the exhibit.

FortiGate has multiple dial-up VPN interfaces incoming on port1 that match only FIRST_VPN.
Which two configuration changes must be made to both IPsec VPN interfaces to allow incoming connections to match all possible IPsec dial-up interfaces? (Choose two.)

Specify a unique peer ID for each dial-up VPN interface.

Use different proposals are used between the interfaces.

Configure the IKE mode to be aggressive mode.

Use unique Diffie Hellman groups on each VPN interface.

NO.44 Which two statements about SLA targets and SD-WAN rules are true? (Choose two.)

When configuring an SD-WAN rule, you can select multiple SLA targets of the same performance SLA.

SD-WAN rules use SLA targets to check if the preferred members meet the SLA requirements.

SLA targets are used only by SD-WAN rules that are configured with Lowest Cost (SLA) or Maximize Bandwidth (SLA) as strategy.

Member metrics are measured only if an SLA target is configured.

NO.45

Two hub-and-spoke groups are connected through a site-to-site IPsec VPN between Hub 1 and Hub 2. The administrator configured ADVPN on both hub-and-spoke groups.
Which two outcomes are expected if a user in Toronto sends traffic to London? (Choose two.)

London generates an IKE information message that contains the Toronto public IP address.

Traffic from Toronto to London triggers the dynamic negotiation of a direct site-to-site VPN.

Toronto needs to establish a site-to-site tunnel with Hub 2 to bypass Hub 1.

The first packets from Toronto to London are routed through Hub 1 then to Hub 2.

NO.46 Which CLI command do you use to perform real-time troubleshooting for ADVPN negotiation?

get router info routing-table all

diagnose debug application ike

diagnose vpn tunnel list

get ipsec tunnel list

NO.47 Refer to the exhibit.

The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured latency will make T_MPLS_0 the new preferred member?