Updated Nov-2022 Pass 200-301 Exam - Real Practice Test Questions [Q219-Q241]

20 Nov, 2022 By admin 200-301, Cisco 0 Comments

Updated Nov-2022 Pass 200-301 Exam – Real Practice Test Questions [Q219-Q241]

Rate this post

Updated Nov-2022 Pass 200-301 Exam – Real Practice Test Questions

Download Free Cisco 200-301 Real Exam Questions

Understanding functional and technical aspects of 200-301 CCNA Exam: Cisco Certified Network Associate Network Access

The following will be discussed here:

802.1Q
Describe the need for and basic operations of Rapid PVST+ Spanning Tree Protocol and identify basic operations
Compare Cisco Wireless Architectures and AP modes
Trunk ports
Connectivity
Network Access
Port states (forwarding/blocking)
Describe AP and WLC management access connections (Telnet, SSH, HTTP, HTTPS,
console, and TACACS+/RADIUS)
Native VLAN
PortFast benefits
Configure and verify interswitch connectivity
Default VLAN
Configure the components of a wireless LAN access for client connectivity using GUI only such as WLAN creation, security settings, QoS profiles, and advanced WLAN settings
Root port, root bridge (primary/secondary), and other port names

Q219. Drag and drop the correct address space on the left to the lPv6 multicast feature or protocol on the right.

Q220. Refer to the exhibit.

With which metric was the route to host 172.16.0.202 learned?

110

38443

3184439

Explanation
Both the line “O 172.16.0.128/25” and “S 172.16.0.0/24” cover the host 172.16.0.202 but with the “longest (prefix) match” rule the router will choose the first route.

Q221. Which configuration ensures that the switch is always the root for VLAN 750?

Switch(config)#spanning-tree vlan 750 priority 38003685

Switch(config)#spanning-tree vlan 750 root primary

Switch(config)#spanning-tree vlan 750 priority 614440

Switch(config)#spanning-tree vlan 750 priority 0

Although the spanning-tree vlan 10 root primary command will ensure a switch will have a bridge priority value lower than other bridges introduced to the network, the spanning-tree vlan 10 priority 0 command ensures the bridge priority takes precedence over all other priorities.

Q222. A frame that enters a switch fails the Frame Check Sequence. Which two interface counters are incremented?
(Choose two)

runts

giants

frame

CRC

input errors

Explanation
Whenever the physical transmission has problems, the receiving device might receive a frame whose bits have changed values. These frames do not pass the error detection logic as implemented in the FCS field in the Ethernet trailer. The receiving device discards the frame and counts it as some kind of input error.
Cisco switches list this error as a CRC error. Cyclic redundancy check (CRC) is a term related to how the FCS math detects an error.
The “input errors” includes runts, giants, no buffer, CRC, frame, overrun, and ignored counts.
The output below show the interface counters with the “show interface s0/0/0” command:

Q223. Refer to the exhibit.

Which type of configuration is represented in the output?

Ansible

JSON

Chef

Puppet

Q224. Which command should you enter to configure a single port to bypass the spanning-tree Forward and Delay timers?

spanning-tree portfast bpdufiter default

spanning-tree portfast default

spanning-tree portfast

spanning-tree portfast bpduguard default

Q225. Drag and drop the functions from the left onto the correct network components on the right

Q226. Refer to the exhibit. After you apply the given configuration to arouter, the DHCP clients behind the device connot communicate with hosts outside of their subnet.
Which action is most likely to correct the problem?

Configure the dns server on the same subnet as the clients

Activate the dhcp pool

Correct the subnet mask

configure the default gateway

Q227. Refer to Exhibit.

The loopback1 interface of the Atlanta router must reach the loopback3 interface of the Washington router.
Which two static host routes must be configured on the NEW York router? (Choose two)

ipv6 route 2000::1/128 2012::1

ipv6 route 2000::3/128 2023::3

ipv6 route 2000::3/128 s0/0/0

ipv6 route 2000::1/128 2012::2

ipv6 route 2000::1/128 s0/0/1

Q228. What is a function of Wireless LAN Controller?

use SSIDs to distinguish between wireless clients.

send LWAPP packets to access points.

monitor activity on wireless and wired LANs

Explanation
Lightweight APs (LAPs) is devices require no initial configuration. LAPs use the Lightweight Access Point Protocol (LWAPP) to communicate with a WLAN controller (WLC), as shown in the below figure.
Controller-based APs are useful in situations where many APs are required in the network. As more APs are added, each AP is automatically configured and managed by the WLC.

Q229. Drag drop the descriptions from the left onto the correct configuration-management technologies on the right.

Q230. Refer to the exhibit.

An engineer deploys a topology in which R1 obtains its IP configuration from DHCP. If the switch and DHCP server configurations are complete and correct. Which two sets of commands must be configured on R1 and R2 to complete the task? (Choose two)

R1(config)# interface fa0/0
R1(config-if)#ip address dhcp
R1(config-if)# no shutsown

R1(config)# interface fa0/0
R1(config-if)#ip helper-address 192.0.2.2

R2(config)# interface gi0/0
R2(config-if)#ip address dhcp

R1(config)# interface fa0/0
R1(config-if)#ip helper-address 198.51.100.100

R2(config)# interface gi0/0
R2(config-if)#ip helper-address 198.51.100.100

Q231. An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office.
What is causing the problem?

There is an area ID mismatch.

There is a PPP authentication issue; a password mismatch.

There is an OSPF hello and dead interval mismatch.

There is a missing network command in the OSPF process on R5.

Q232. Which two actions influence the EIGRP route selection process? (Choose two)

The router calculates the reported distance by multiplying the delay on the exiting Interface by 256.

The router calculates the best backup path to the destination route and assigns it as the feasible successor.

The router calculates the feasible distance of all paths to the destination route

The advertised distance is calculated by a downstream neighbor to inform the local router of the bandwidth on the link

The router must use the advertised distance as the metric for any given route

Explanation
The reported distance (or advertised distance) is the cost from the neighbor to the destination. It is calculated from the router advertising the route to the network. For example in the topology below, suppose router A & B are exchanging their routing tables for the first time. Router B says “Hey, the best metric (cost) from me to IOWA is 50 and the metric from you to IOWA is 90” and advertises it to router A.
Router A considers the first metric (50) as the Advertised distance. The second metric (90), which is from NEVADA to IOWA (through IDAHO), is called the Feasible distance.

The reported distance is calculated in the same way of calculating the metric. By default (K1 = 1, K2 = 0, K3
= 1, K4 = 0, K5 = 0), the metric is calculated as follows:

Q233. which type of IPv6 address is publicly routable in the same way as IPv4 public address?

global unicast

link-local

unique local

multicast

Q234. Which three statements about Syslog utilization are true? (Choose three.)

Utilizing Syslog improves network performance

The Syslog server automatically notifies the network administrator of network problems

A Syslog server provides the storage space necessary to store log files without using router disk space

There are more Syslog messages available within Cisco IOS than there are comparable SNMP trap messages.

Enabling Syslog on a router automatically enables NTP for accurate time stamping

A Syslog server helps in aggregation of logs and alerts.

Q235. Drag and drop the network protocols from the left onto the correct transport services on the right.

Q236. An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any one of three addresses:
192.168.3.1, 192.168.3.2, or 192.168.3.3. Which configuration should be used?

Section: IP Services

Q237. How does STP prevent forwarding loops at OSI Layer 2?

TTL

MAC address forwarding

Collision avoidance.

Port blocking

Q238. Which two conditions must be met before SSH can operate normally on a Cisco IOS switch? (Choose two.)

IP routing must be enabled on the switch.

A console password must be configured on the switch.

Telnet must be disabled on the switch.

The switch must be running a k9 (crypto) IOS image.

The ip domain-name command must be configured on the switch.

Section: Network Access
Explanation/Reference: https://www.cisco.com/c/en/us/support/docs/security-vpn/secure-shell-ssh/4145-ssh.html

Q239. Which type of traffic Is sent with pure iPsec?

broadcast packets from a switch that is attempting to locate a MAC address at one of several remote sites

multicast traffic from a server at one site to hosts at another location

spanning-tree updates between switches that are at two different sites

unicast messages from a host at a remote site lo a server at headquarters

“The original poster makes a correct observation that EIGRP does not work in a pure IPSEC environment. IPSEC was designed to process unicast traffic.

Q240. Drag the IPv6 DNS record types from the left onto the description on the right.

https://ns1.com/resources/dns-types-records-servers-and-queries#:~:text=Address%20Mapping%20record%20(A%20Record,a%20hostname%20to%20another%20hostname.