NSE6_FSW-7.2 Popular Exams – Premium VCE Dumps

15 Dec, 2025 By admin

2025 Updated Verified NSE6_FSW-7.2 dumps Q&As – 100% Pass Guaranteed [Q33-Q54]

2025 Updated Verified NSE6_FSW-7.2 dumps Q&As – 100% Pass Guaranteed

Provide Valid Dumps To Help You Prepare For Fortinet NSE 6 – FortiSwitch 7.2 Exam

Candidates for the Fortinet NSE6_FSW-7.2 exam should have a strong understanding of networking fundamentals, as well as experience working with Fortinet products. NSE6_FSW-7.2 exam is designed to test the candidate’s knowledge of the FortiSwitch platform and their ability to configure and manage various features and functions of the device. Upon passing the exam, candidates will receive the Fortinet NSE 6 – FortiSwitch 7.2 certification, which is recognized in the industry as a mark of expertise in Fortinet products and networking.

NO.33 Which statement about the IGMP snooping querier when enabled on a VLAN is true?

Active multicast receiver entries are aging on each IGMP query sent on the VLAN

IGMP reports on the VLAN are forwarded to all switch ports.

The setting can only be enabled using the FortiSwitch CLI.

All other indirectly connected switches will be unable to get IGMP multicast traffic.

NO.34 Refer to the diagnostic output:

Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?

It is a MAC address of FortiLink interface on FortiGate.

It is a MAC address of a switch that accepts multiple VLANs.

It is a MAC address of an upstream FortiSwitch.

It is a MAC address of FortiGate in HA configuration.

NO.35 Refer to the exhibit.

Which two statements best describe what is displayed in the FortiLink debug output shown in the exhibit? (Choose two.)

FortiSwitch is sending FortiLink heartbeats to FortiGate.

FortiSwitch is discovered and authorized by FortiGate.

FortiSwitch is in a waiting state to join the stack group on FortiGate.

FortiSwitch is ready to push its new hostname to FortiGate.

NO.36 Which is a requirement to enable SNMP v2c on a managed FortiSwitch?

Create an SNMP user to use for authentication and encryption.

Specify an SNMP host to send traps to.

Enable an SNMP v3 to handle traps messages with SNMP hosts.

Configure SNMP agent and communities.

NO.37 What are two reasons why time synchronization between FortiGate and its managed FortiSwitch is critical in switch management? (Choose two.)

FortiSwitch does not retain its time after a reboot, which gets reset after each reboot.

FortiSwitch will not be able to become an NTP server for downstream devices.

FortiSwitch cannot complete the DTLS handshake used in the CAPWAP tunnel.

FortiSwitch will not allow other FortiSwitch devices in the chain be discovered by FortiGate.

NO.38 How does FortiGate handle configuration of flow tracking sampling if you export the settings to a managed FortiSwitch stack with sampling mode set to perimeter is true?

FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces.

FortiGate configures FortiSwitch to perform ingress sampling on all switch interfaces, except ICL and ISL interfaces.

FortiGate configures and enables flow sampling on FortiSwitch but does not change existing sampling settings of interfaces.

FortiGate configures and enables egress sampling on all management interfaces.

NO.39 Which two statements about the FortiLink authorization process are true? (Choose two.)

The administrator must manually pre-authorize FortiGate on FortiSwitch by adding the FortiGate serial number.

FortiSwitch requires a reboot to complete the authorization process.

A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization.

FortiLink authorization sets the FortiSwitch management mode to FortiLink.

NO.40 Refer to the exhibits.

Port1 and port2 are the only ports configured with the same native VLAN 10.
What are two reasons that can trigger port1 to shut down? (Choose two.)

port1 was shut down by loop guard protection.

STP triggered a loop and applied loop guard protection on port1.

An endpoint sent a BPDU on port1 that it received from another interface.

Loop guard frame sourced from port 1 was received on port 1.

NO.41 Exhibit.

What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)

The FortiSwitch model is equipped with a maximum of 54 interfaces.

The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.

The port full speed prior the split was 100G SFP+

The split port can be assigned to native VLAN

NO.42 Which two statements about DHCP snooping enabled on a FortiSwitch VLAN are true? (Choose two.)

Enabling DHCP snooping on a FortiSwitch VLAN ensures requests and replies are seen by all DHCP servers.

switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks.

By default, all FortiSwitch ports are set to forward client DHCP requests to untrusted ports.

Settings related to DHCP option 82 are only configurable through the CLI

NO.43 Which LLDP-MED Type-Length-Values does FortiSwitch collect from endpoints to track network devices and determine their characteristics?

Network policy

Power management

Location

Inventory management

NO.44 Refer to the diagnostic output:

What makes the use of the sniffer command on the FortiSwitch CLI unreliable on__port__23?

The types of packets captured is limited.

Just the port egress payloads are printed on CLI.

Only untagged VLAN traffic can be captured.

The switch port might be used as a trunk member

The switch port might be used as a trunk member. When a switch port is configured as a trunk, it can carry traffic for multiple VLANs. If the sniffer is set up without specifying VLAN tags or a range of VLANs to capture, it may not accurately capture or display all the VLAN traffic due to the volume and variety of VLAN-tagged packets passing through the trunk port. This limitation makes using the sniffer on a trunk port unreliable for capturing specific VLAN traffic unless properly configured to handle tagged traffic.

NO.45 Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?

All ports have auto-discovery enabled by default.

No ports are enabled by default for auto-discovery. This must be configured under config switch interface.

The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.

The last four switch ports on FortiSwitch have auto-discovery enabled by default.

NO.46 Refer to the diagnostic output:

Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?

It is a MAC address of FortiLink interface on FortiGate.

It is a MAC address of a switch that accepts multiple VLANs.

It is a MAC address of an upstream FortiSwitch.

It is a MAC address of FortiGate in HA configuration.

NO.47 What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate?

FortiGate multi-tenancy

Multi-chassis link aggregation trunk

FortiGate clustering protocol

FortiLink split interface

NO.48 Refer to the diagnostic output:

What makes the use of the sniffer command on the FortiSwitch CLI unreliable on__port__23?

The types of packets captured is limited.

Just the port egress payloads are printed on CLI.

Only untagged VLAN traffic can be captured.

The switch port might be used as a trunk member

NO.49 Which two statements about VLAN assignments on FortiSwitch ports are true? (Choose two.)

Configure a native VLAN on the FortiLink

Assign an IP address and subnet mask to FortiSwitch VLANs

Only assign one native VLAN on a port

Assign untagged VLANs using FortiGate CLI

NO.50 Which two statements about DHCP snooping enabled on a FortiSwitch VLAN are true? (Choose two.)

Enabling DHCP snooping on a FortiSwitch VLAN ensures requests and replies are seen by all DHCP servers.

switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks.

By default, all FortiSwitch ports are set to forward client DHCP requests to untrusted ports.

Settings related to DHCP option 82 are only configurable through the CLI

NO.51 Exhibit.

Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)

These two routes have a higher administrative distance value available to the destina-tion networks.

These two routes will become primary, if the best routes are removed.

These two routes will be used as load-balancing routes.

These two routes are available in the hardware routing table.

NO.52 In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)

Switch the FortiLink interface to the target VDOM.

Remove the managed FortiSwitch and allocate ports directly on FortiSwitch.

Create a virtual port pool on the FortiGate CLI.

Assign a port to a VDOM directly on the managed FortiSwitch.

NO.53 Exhibit.

The exhibit shows the current status of the ports on the managed FortiSwitch.
Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?

Port23 is a member of a trunk that uses the Access-1 FortiSwitch senal number as the name of the trunk.

Port23 is configured as the dedicated management interface.

A standalone switch with the showm serial number is connected on por123.

Ports connect to adjacent FortiSwitch devices will show their.serial number as the na-tive VLAN

NO.54 Refer to the exhibits

Traffic arriving on port2 on FortiSwitch is tagged with VLAN ID 10 and destined for PC1 connected on port1. PC1 expects to receive traffic untagged from port1 on FortiSwitch.
Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1? (Choose two.)

Add the MAC address of PCI as a member of VLAN 10.

Add VLAN ID 10 as a member of the untagged VLANs on port1.

Remove VLAN 10 from the allowed VLANs and add it to untagged VLANs on port1.

Enable Private VLAN on VLAN 10 and add VLAN 20 as an isolated VLAN.

The NSE6_FSW-7.2 exam is part of Fortinet’s Network Security Expert (NSE) program, which is designed to recognize individuals who have the knowledge and skills required to design, configure, and troubleshoot Fortinet solutions. NSE6_FSW-7.2 exam focuses on FortiSwitch version 7.2, which is the latest release of the product.

Achieve Success in Actual NSE6_FSW-7.2 Exam NSE6_FSW-7.2 Exam Dumps: https://www.premiumvcedump.com/Fortinet/valid-NSE6_FSW-7.2-premium-vce-exam-dumps.html

Premium VCE Dumps

Premium VCE Dumps

Tag Archives: NSE6_FSW-7.2 Popular Exams

2025 Updated Verified NSE6_FSW-7.2 dumps Q&As – 100% Pass Guaranteed [Q33-Q54]