Q81. An LTM Specialist needs to enable TCP connection re-use for a non-HTTP application. The application uses a simple request response protocol where each request and response is contained within a single packet.
Which configuration option should the LTM Specialist adjust?

Q82. An LI M device is experiencing a high volume of traffic. The virtual server is struggling under the load. The problem appears to be on the server side connections. The virtual server is accepting connections . The virtual server is accepting connections on https and is configured with an SSL profile and http pool.
What should be added to increase the performance of the device?

Q83. An LTM device an application that requires all connections to be secured via SSL The device must verify that request contain a specific cookie before allowing the request to be sent to the pool member.
Which virtual server type should an LTM Specialist configure on the LTM device?

Q84. Refer to the exhibit.

The http monitor is applied to a pool All members are enabled One pool member stops responding TCP port 80. The server still responds to ping.
What is the resulting status of this pool member?

Q85. Two LTM devices must be manually configured to restrict in the same Device Group.
What is the correct order of steps to meet this requirement?

Q86. An LTM Administrator receives an email from the NOC stating that the switch connected to the backend server was shut down for maintenance. The BIG-IP device handles only UDP traffic. The BIG IP device did not fail over to a DR location when no pool members were available.
When the LTM Administrator checks the pool, it confirms that the monitor is still marking UP the pool member.
A tcpdump of the traffic shows the following output:

A list of the monitor configuration shows the following:

Which two modifications to the LTM configuration will mark this pool member down, when the switch is down? (Choose two.)

Q87. Remote office users are having performance issues with a virtual hosted on the F5 LTM. The LTM Specialist reviews the configuration for the virtual server and determine that some settings are set with default profiles.
Which profile should the LTM Specialist enable to improve virtual server performance?

Q88. An LTM Specialist plans to enable connection mirroring for a virtual server in an HA environment.
What must the LTM Specialist consider before implementing the configuration change?

Q89. Refer to the exhibit.

An LTM Specialist configures the two syslog destination Syslog destination #1 can receive messages but the syslog destination #2 can NOT receive messages.
Which command sill correct the issue?

Q90. A design requires the LTM device to become HA standby when the one of the two physical interface on the External trunk is down the External trunk is an interface on the External VLAN Which TMOS command enables this behavior?

Q91. An LTM Specialist has trouble with SNMP traps in the management network The ITM Specialist takes the network capture shown to troubleshoot:

What should the UM Specialist change to capture packets related to this workflow?

Q92. Refer to the exhibit

Given the bigip conf extract shown where the servers only talk http on port 80, which node will receive the next user request?

Q93. in which Application Visibility and Reporting (AYR) profile must the SMTP profile be defined to configure notifications via email?

Q94. Refer to the exhibit.

The LTM devices LTM3 and LTM2 have four Traffic Groups defined with approximately the sar of failover objects defined in each group.
– Traffic Groups A and C have Default Device set to LTM1
– Traffic Groups Band D have Default Device set to LTM2.
– Traffic Groups B and C do NOT have Auto Failback enabled. Traffic Groups A and D have Auto Failback enabled with a timeout value of 60 seconds.
– Traffic Groups A and D have Auto Fallback enabled with a timeout value of 60 seconds.
Both LTM devices are healthy and able to pass traffic for any Traffic Group.
LTM1 loses connectivity on interface 1.4. The LTM Specialists notified 60 seconds after the interface goes down.
What is the state of the Traffic Groups on each LTM device?

Q95. An LTM Specialist configures a new virtual server with a single pool member. The LTM Specialist has NOT defined a health monitor for the pool, pool member or node.
What is the status of the virtual server?

Q96. An TLM Specialist needs to configure a virtual server to terminate SSL connection on the LTM device.
Cryptographic information must be re-authorized for SSL sessions that remain open for longer than 30 seconds.
Which settings should the LTM Specialist configure in the client SSL profile?

Q97. Exhibit.

– The ITM devices LTM 1 and LTM2 are configured in Device Group X (Sync-Failover)
– LTM3 and LTM4 are configured in Device Group Y (Sync-Only)
– An LTM specialist configures Device Group Z (Sync-Only) to keep several profiles in (sync-Only) to keep several profiles in sync across all devices.
– Device GROUP X has four Traffic Groups A, B, C and D configured.
– Device Group Y has four Traffic Groups E, F, G, and H configured
– Auto Fallback IS NOT Enabled.
– Each Device group is healthy and able to pass traffic for any traffic group assigned to that Device Group.
The data center that contains LTM2 and LTM4 loses power. After 10 minutes; power is restored and all devices are up and healthy.
What is the state of each Traffic Group on each ITM device after power is restored?
A)

B)

C)

D)

Q98. An LTM Specialist needs to create two virtual servers.
The application has links for both HTTP and HTTPS version of application. The client must be persistence to a pool member, no matter which virtual server is accessed.
What must be selected in the Source Address Affinity persistence profile?

Q99. A BIG IP system load balances connections to a web application. A TCP-based Denial of Service attack against the web application is occurring, which has caused very high memory utilization on the LTM device due to stale TCP connections.
Which TCP profile option should be used to reduce memory utilization?

Q100. An LTM Specialist observes decreased performance and intermittent connection reap LTM system.

Based on the configuration, which action will address these issues?